How Do You Calculate a PoE Power Budget?

PoE power budget calculation: 802.3af/at/bt classes, IR and heater load, class-based allocation, total switch budget, PoE priority and an example calculation for UPS runtime.
Technical summary
Technology
IEEE 802.3af/at/bt, PoE switch, UPS
Topic
Power budget
Level
Intermediate
In this article9 sections

Cameras work fine by day, but at night when IR kicks in, or in winter when the heaters turn on, a few randomly drop out. The switch log shows the budget being exceeded or port power being cut. This picture almost always means the power budget was calculated with nominal consumption. PoE (Power over Ethernet) carries both data and power to the camera over a single cable and simplifies installation; but if the calculation isn’t based on the worst case, the failure shows up at the worst moment. Below are PoE standards, how to read camera consumption, an example switch and UPS calculation and troubleshooting on site. Even if the switch’s power budget is sufficient, the risk of heating in PoE cable bundles is assessed separately on crowded cable routes.

PoE standards and power classes

Standard Common name PSE output (per port) Delivered to the device (approx.)
IEEE 802.3af PoE (Type 1) 15,4 W 12,95 W
IEEE 802.3at PoE+ (Type 2) 30 W 25,5 W
IEEE 802.3bt Type 3 (4-pair) 60 W ~51 W
IEEE 802.3bt Type 4 (4-pair) 90 W ~71 W

The PSE (Power Sourcing Equipment) is the switch supplying power; the PD (Powered Device) is the camera. The difference between them is power loss in the cable, highest on 100-meter runs. Some manufacturers’ proprietary names such as “PoE++” or “Hi-PoE” may behave outside the standard; the IEEE standard and class should be written into the specification. Passive PoE adapters apply voltage without the standard handshake. They have no place in a corporate camera network.

Read camera consumption correctly

Camera datasheets usually list two values: typical consumption and maximum consumption. The budget calculation uses the maximum value, because:

  • Consumption rises noticeably when IR LEDs turn on at night.
  • Outdoor cameras with heaters draw a few extra watts in the cold.
  • PTZ cameras need much more power while moving and with the heater on; most require 802.3at or 802.3bt.
  • Some cameras reserve power from the switch based on their class announcement; the switch’s “allocate by class” or “allocate by actual consumption” mode affects the budget.

There’s a common misconception on site with allocate-by-class mode. If a camera that actually draws 7–8 W announces itself as PoE+ class, the switch reserves 30 W for that port. While total measured consumption looks low, the switch refuses to power a new port. The figure on the watt meter and the reserved budget are different things. Which one is used is checked in the switch’s PoE management settings and datasheet; on devices that support power negotiation via LLDP, allocation can be closer to the real need.

Example calculation: a 24-port camera switch

Instrument Quantity Worst case (W) Total (W)
Indoor dome (IR) 14 8 112
Outdoor bullet (IR + heater) 6 18 108
PTZ (802.3bt Type 3) 2 45 90
Total load 310
Recommended PoE budget with 30% headroom ≥ 403

In this case, a switch with a 370 W PoE budget isn’t enough; you need a model with a budget of 400 W or more, or the load split across two switches. You should also check that the ports the PTZs connect to support 802.3bt: some switches provide high power only on certain ports.

There’s another reason for headroom: the first power-up after an outage. When the system comes back from a long outage on a winter night, all cameras power up at once, and the heaters of outdoor cameras run at full power to warm up the cold housings. A budget that’s enough in normal operation can be exceeded during those few minutes. Some switches offer features such as delayed per-port power-up or keeping PoE during a reboot; use them if available.

Per-port limit and total budget

There are two separate limits: the maximum power that can be delivered per port and the total power the switch can deliver across all ports. Every port on a 48-port switch may be PoE+, but the total budget may be, say, 740 W rather than 48 × 30 W = 1440 W. When the budget is exceeded, the switch cuts power to some ports according to their priority setting. Ports with critical cameras should be given high PoE priority.

If no priority is set, the switch decides which port to shut down by its own rule; on many models this depends on the port number. If the main entrance camera is on port 47, it may be the first to go. The priority list is kept with the camera inventory and updated when ports change.

Cable and environmental effects

  • Loss increases on runs close to 100 meters and with low-quality (CCA) cable; solid copper Cat6 is preferred.
  • High-power PoE causes cables to heat up; this effect grows in bundled cables.
  • In industrial field cabinets, the switch’s operating temperature range may reduce the PoE budget with temperature (derating); check the datasheet.

CCA (copper-clad aluminum) cable seems to work for data on short runs; at high power and on long runs the voltage drop increases, and a PTZ reboots while moving. Because the fault is intermittent, the cable is the last place suspected. It should be one of the first places checked.

Troubleshooting on site

For a camera that drops out randomly, first check the switch’s PoE status: power allocated and drawn per port, the remaining total budget and the PoE event log. On Cisco IOS-based switches, this is shown with the show power inline command; other vendors have an equivalent command and web interface screen. If drop-outs cluster at night or in the cold, the calculation was done with nominal consumption. If it’s tied to a single port, the cable, the connector or the camera itself is suspect; testing the same camera with a short, good-quality cable quickly tells them apart.

UPS runtime calculation

For cameras to work during an outage, the switches are connected to a UPS. A simple approach:

UPS load (W) = the switch’s own consumption + total PoE load
Required battery energy (Wh) ≈ UPS load × target runtime (hours) ÷ inverter efficiency

Example: switch 60 W + PoE 310 W = 370 W; with a 30-minute target and 90% efficiency, about 206 Wh of usable battery energy is needed. Headroom is added for battery ageing and depth of discharge; the exact runtime is verified with the UPS manufacturer’s runtime tables. Details: UPS and power continuity.

Don’t forget the recording side. If the cameras run on UPS but the NVR or recording server, or the backbone switch in between, is outside the UPS, video is produced but not recorded. UPS coverage must include the whole chain from camera to disk.

Checklist

  • Are the maximum consumption and PoE class listed for each camera?
  • Does the total load stay below 70–80% of the switch budget?
  • Do PTZ and high-power device ports support the required standard?
  • Is PoE priority defined for critical cameras?
  • Are switch and UPS monitoring alarms (PoE overload, port down) active?

Frequently asked questions

The switch has a 370 W PoE budget; is it enough if I connect 24 cameras at 15 W?

24 × 15 W = 360 W fits in theory, but leaves no headroom. When heaters or IR turn on, or cable loss is added, the switch may cut power to some ports. You need to leave 20–30% headroom and base the calculation on worst-case consumption.

Can a camera be connected over PoE beyond 100 meters?

A standard Ethernet link is limited to 100 meters. For more distant points, fiber and a field switch, a PoE extender or suitable media converters are used.

Is it enough to connect the PoE switch to a UPS?

For cameras to keep working during an outage, yes, PoE switches must be covered by the UPS. UPS power is calculated from the switch’s own consumption plus the total PoE load and efficiency loss.

Fiber backbone planning for remote points is covered in our fiber backbone service, and switch selection and network design in our PoE switch and camera network service.

Support

Contact us for support or a discovery session on this topic.

Contact form
[email protected]

Eretek Video Surveillance

IP cameras, recording and central management infrastructure. We plan blind spots, retention periods and the camera network around the risks of each site.

Knowledge Center

Other articles