IR Range and Night Image: Camera Performance in Low Light

Choosing a night vision camera: minimum illumination values, IR range vs. real working distance, color night images, IR reflection and a night test checklist.
Technical summary
Technology
IR LEDs (850/940 nm), IR-cut filter (ICR), Smart IR, F-number, white-light cameras, IEC 62471
Topic
Choosing cameras and lighting for low light
Level
Intermediate
Prerequisites
  • Exposure and gain concepts
  • Pixel density (px/m) calculation
In this article8 sections

A camera that looks sharp by day turns at night into an image that’s noisy, blurred or lights up only the few meters in front of it. The real test of a camera system is the night, and the “0.001 lux” or “IR 60 m” on the datasheet doesn’t tell you the result of that test; those values are compared without stating the conditions under which they were measured. Below we cover the factors that determine the image in low light, how to read minimum illumination and IR range values, IR problems commonly seen on site and the decision on external lighting.

Factors that determine the image in low light

Night image quality depends on two things: how many photons reach the sensor, and how well the sensor separates those photons from noise. The parameters affecting these two quantities:

  • Sensor and pixel size: In the same optical format, as resolution increases the pixels get smaller and the light per pixel falls. An 8 MP camera with the same sensor size can be noisier at night than a 4 MP camera.
  • Lens aperture (F-number): Light collected is inversely proportional to the square of the F-number. An F1.0 lens collects about 2.56 times (1.6²) more light than an F1.6 lens.
  • Exposure time: A long shutter collects more light but produces motion blur. This balance is covered in detail in the camera exposure settings article.
  • Image processing: Noise reduction and gain limits clean up the image but can also soften detail.
  • Light added to the scene: Built-in IR LEDs, external IR illuminators, white light or existing site lighting.

The decisive one is often the last item. No sensor can make up for light that doesn’t reach the target. No light, no image.

Reading minimum illumination values

“Minimum illumination” is the lowest scene illuminance at which the camera produces a usable image under a given condition. A value without its condition is meaningless. The typical wording on a datasheet looks like this:

Color: 0.005 lux @ (F1.6, AGC ON)
B/W:   0.0005 lux @ (F1.6, AGC ON)
0 lux with IR

When comparing, look at these details:

Condition Why it matters
F-number A value measured at F1.0 can’t be compared directly with one at F1.6
Shutter time A value measured at a long time such as 1/3 s doesn’t reflect real use
AGC (gain) An image measured at maximum gain can be very noisy
IRE level How bright the image is considered to be (e.g. 30 or 50 IRE)
Color / black-and-white The B/W value refers to the state with the IR-cut filter removed

These conditions are missing from most datasheets and aren’t the same between brands. The minimum illumination value is useful for ranking one manufacturer’s models among themselves; deciding between manufacturers requires a night pilot test. “0 lux with IR” only says the camera gives an image in full darkness with its built-in IR. It says nothing about the quality.

IR range and real working distance

Built-in IR LEDs usually work around 850 nm. In day mode, the IR-cut filter between the lens and sensor blocks infrared; when light falls, the filter lifts mechanically (ICR) and the camera switches to black-and-white mode. The “click” you hear from a camera at dusk is this filter moving.

The IR range on the datasheet is the distance at which a given target can be made out in the image, and the measurement condition is often not stated. Two physical facts decide the matter:

  1. The inverse square law: Illuminance from a point source falls with the square of the distance. If the distance doubles, IR illuminance on the target drops to a quarter. The camera makes up for this loss with gain; the far area becomes noisy.
  2. Matching beam angle to field of view: If the IR LEDs’ beam angle is narrower than the lens’s field of view, the edges of the frame stay dark; if it’s wider, the light doesn’t reach far points. That’s why varifocal models that adapt the beam angle as zoom changes are preferred.

In practice, the IR range is an upper limit for noticing that a person is “there” in the image. The clean image needed for recognition or identification is achieved well below this distance. Take the distance used in the project from a night test, not from the datasheet. For the required pixel density, see the IP camera system design guide.

940 nm IR LEDs are almost invisible to the human eye; they’re preferred where covert monitoring is needed. A silicon sensor’s sensitivity at this wavelength is markedly lower than at 850 nm; with the same LED power you get shorter range and a darker image. Some 850 nm LEDs glow faint red when viewed up close and give away the camera’s position. That alone isn’t a sufficient reason to choose 940 nm.

Color night images and white light

Under IR the image is black-and-white, and some fabrics and paints appear in different tones under IR than in daylight; a dark jacket can come out light gray. If clothing and vehicle color matter in incident review, color night images gain value. There are two approaches:

  • Large aperture and large sensor: A lens around F1.0 and a large-pixel sensor keep the image in color in a scene with street or building lighting. They don’t help in full darkness.
  • White-light cameras: A built-in white LED lights the scene with visible light. It’s a deterrent; but it has consequences such as light pollution, light spilling onto neighboring plots or roads, attracting insects and energy consumption. Some models offer a hybrid mode that uses IR by default and switches to white light only when a person or vehicle is detected.

A thermal camera relies on heat, not light; it detects in full darkness but doesn’t give an identification image. Its uses are explained separately in the thermal camera guide.

IR reflection and site problems

A significant share of night image problems come not from the camera but from mounting. The fault ticket says “the camera can’t see at night”; on site, the cause is often one of these:

  • Near-surface reflection: A wall, eave, pole or sign right in front of the camera reflects IR back; the camera sets exposure for this bright area and the far area goes dark. A near surface at the edge of the frame looks harmless by day.
  • Mounting behind glass: IR reflects off the glass back into the lens. IR must be turned off on a camera behind a window.
  • Dome: A dirty, scratched or poorly seated dome scatters IR from inside, creating a blurry halo in the image. The foam separator ring inside the dome must be in place. It’s common for the ring to shift after cleaning.
  • Spider webs and insects: IR LEDs attract insects, and insects attract spiders. A web in front of the lens turns into a bright veil at night and constantly triggers motion detection.
  • Rain, fog and snow: Drops and particles close to the lens scatter IR back. Moving the light source away from the camera axis reduces this effect.
  • Overexposed near target: The face of a person approaching the camera is clipped white by IR. Smart IR or similar functions limit this by lowering LED power according to the scene.

The external lighting decision

Built-in IR is enough for most indoor and short-range outdoor points. Consider external lighting in these situations:

Status Why Option
Identification distance beyond the built-in IR limit Insufficient light on the target Narrow-angle external IR illuminator
Large area, multiple cameras Each camera’s own IR insufficient and uneven Area IR lighting or general lighting
Rain, fog, insect problems Light close to the axis is scattered back Illuminator positioned apart from the camera
Color information needed IR doesn’t give color White light, improving existing lighting
Plate reading Reflective plates and short shutter Dedicated LPR camera with IR lighting

External illuminators need power and mounting infrastructure. Cameras with IR on also consume more at night than by day; calculate the switch budget with worst-case consumption (PoE power budget calculation). Port power being exceeded and the camera restarting when IR kicks in at night is a known fault on site. The eye safety class of high-power IR illuminators is specified under IEC 62471; plan mounting height and maintenance access based on this information. For the standard, see the IEC publications catalog.

Night test checklist

  • The test was done in full darkness, not at dusk, with site lighting in its operating condition (on or off).
  • For each camera, a recording was made with a person walking at the target distance; the recording was reviewed frame by frame and the required image level verified.
  • The light level at which the day/night switch happens and the focus shift during the switch were checked.
  • There’s no near-surface reflection, dome halo or glass reflection at the edge of the frame.
  • It was checked that the face of a person approaching the camera isn’t overexposed.
  • Night shutter and gain limits are documented; slow shutter is off.
  • Night average and peak bitrate values were recorded and compared with the storage calculation.
  • Several nights of event logs were reviewed for false motion alarms caused by spider webs and insects.
  • Power, scheduling and fault tracking have been defined for external illuminators.

High-contrast scenes such as backlight are a separate class of problem; they’re covered in the WDR and backlight camera selection article. For outdoor areas where night performance is decisive, see our outdoor and perimeter security cameras page, and for the design as a whole, our IP camera system design service.

Frequently asked questions

If the datasheet says 50 m IR, can I identify a person at 50 m?

Usually not. The IR range is often the distance at which a target with good reflectivity can be made out in the image. The pixel density and low noise needed for identification are achieved well below this distance; measure the real working distance in a night test.

Should I choose 850 nm or 940 nm IR?

An 850 nm LED gives off a faint red glow, but its range is longer because sensor sensitivity is higher. 940 nm is almost invisible to the human eye; at the same power it gives shorter range and a darker image. If concealment isn’t needed, 850 nm is more efficient.

Why does a camera placed behind a window show nothing at night?

The camera’s own IR light reflects back off the glass into the lens and covers the image with a bright blotch. If night monitoring through glass is needed, turn off the camera’s IR and use separate lighting on the outside, or move the camera outdoors.

Do cameras that give color night images replace IR?

If there’s street or building lighting, cameras with large apertures and large sensors can give a color image. In full darkness, white light has to be added; its light pollution, impact on neighboring areas and energy consumption should be assessed separately.

Support

Contact us for support or a discovery session on this topic.

Contact form
[email protected]

Eretek Video Surveillance

IP cameras, recording and central management infrastructure. We plan blind spots, retention periods and the camera network around the risks of each site.

Knowledge Center

Other articles