Car Park and Vehicle Entry Camera Systems: Barriers, LPR and Coverage

Car park camera systems: a plate camera and an overview camera per lane, headlight glare settings, barrier integration, column and lighting issues in indoor car parks.
Technical summary
Technology
LPR/ANPR, IR illumination (850 nm), inductive loop detector, Wiegand, dry contact relay, WDR
Topic
Holistic camera design for car park entry–exit, parking and pedestrian areas
Level
Intermediate
Prerequisites
  • Basic IP camera and VMS knowledge
  • Access control and barrier logic
In this article8 sections

The sentence heard most often after an incident in a car park is: “The plate was read, but it’s unclear which vehicle it was.” A car park camera system isn’t just a single plate camera. Entry–exit lanes, barriers and access control, parking areas, ramps, walkways and payment points create separate imaging needs; if you design them independently of each other, you create both blind spots and integration problems. Below we take the car park as a whole and give site decisions in order, from lane geometry to indoor car park lighting.

What’s expected from the cameras

The results expected from cameras in a car park fall into four groups. Each needs a different camera and different settings:

  • Vehicle identity: the plate of each vehicle entering and leaving is recorded with a timestamp and lane information. This is the plate camera’s job.
  • Event context: the vehicle’s type and color, the behavior of the driver and passengers, the barrier opening and closing. This is the overview camera’s job.
  • Damage and theft in the parking area: which section the vehicle parked in, who approached it; needs wide coverage at observation level.
  • Pedestrian safety: recognizable images of people at lift lobbies, stairs, payment machines and exit doors.

The first output of the design is a list showing at what level these goals are needed in each area. In a shopping mall car park, vehicle identity and pedestrian safety come first; in a factory staff car park, matching the entry log with access control matters more. No list, no design.

Camera layout for entry–exit lanes

Each lane is designed with its own camera set. Trying to read two lanes with a single plate camera reduces read quality in both lanes because of angle and focus compromises. This installation usually ends up having to be redone. The layout we recommend per lane:

You are here Camera Purpose Critical setting
In front of the barrier, on the lane axis LPR camera + IR Plate reading Short shutter, narrow view
Beside the barrier, diagonal Fixed overview Vehicle, driver, barrier arm WDR, wide angle
Card reader / intercom Short-range fixed The driver’s face and hand Aligned to reader height
Outside the lane, from above Fixed or PTZ Queue and maneuvering area Observation level

The plate camera’s position is set by where the vehicle stops. When the vehicle stops over the loop detector in front of the barrier, the plate should be in the middle of the camera’s defined read zone. Most manufacturers recommend that the horizontal and vertical angles between the camera and plate not exceed 30 degrees; as the angle increases, characters narrow and recognition confidence drops. For exact values and the pixel width the plate should occupy in the image, follow the manufacturer’s installation guide.

The most common fault at night is headlight glare. A camera reading the front plate looks straight into the headlights. Three methods are used together: IR illumination (usually 850 nm) that brings out the plate’s retroreflective surface, a short exposure time that suppresses the effect of the headlights, and, if possible, reading the rear plate in the entry lane. For the rear plate, the camera is placed behind the vehicle’s stopping point, facing the direction of travel; the headlights don’t face the camera. In this layout, camera height and angle are chosen according to the queue distance so the vehicle behind doesn’t block the plate.

You can find the relationship between shutter, gain and motion blur in the camera exposure settings article, and plate camera selection and how to measure recognition accuracy in the license plate recognition accuracy guide.

Separating overview and plate cameras

A plate camera is a device tuned for reading plates: a narrow field of view, short exposure, strong IR and often a black-and-white night image. These settings sharpen the plate but erase the vehicle’s color, model and the driver. To avoid ending up with “the plate was read but the vehicle is unclear” in a dispute review, each lane should have a separate overview camera. One camera doesn’t do two jobs.

The two cameras’ recordings are linked to the same event in the VMS. When a plate event arrives, the operator sees the plate image and the overview frame from the same second side by side. For this, both cameras’ clocks should be fed from the same NTP source and they should be defined as a camera group in the VMS. The overview camera should also record the movement of the barrier arm; in a “the barrier hit my car” dispute, this is the decisive footage.

Differences between indoor and outdoor car parks

Topic Indoor car park Outdoor car park
Mounting Low ceilings, columns, cable trays Poles, lighting columns, façades
View obstruction Columns and tall parked vehicles Trees, distance, weather
Lighting Artificial, often motion-activated Depends on pole lighting at night
Camera type Fixed dome, corridor mode, fisheye Bullet, PTZ, thermal (perimeter)
Maintenance risk Exhaust soot and dust build up on the dome Rain, spider webs, lightning

In an indoor car park, driving aisles are long and narrow; as in a rack aisle, a 9:16 corridor mode provides efficient coverage. The biggest obstacle is the column. The camera should be placed on the aisle axis, not on a column, and parking spaces behind columns should be seen by a second camera from the opposite direction. Ramps, inter-floor transitions and vehicle lifts are listed as separate points.

Motion-activated lighting makes cameras in an indoor car park switch constantly between color and IR modes. Either a minimum level of lighting is left on, or night mode threshold and delay settings are tuned to the site. Exhaust soot builds a layer on the dome that blurs the image over time. The dome gets dirty, the image softens. The cleaning interval in the maintenance plan is set accordingly.

In an outdoor car park, cameras are mostly mounted on lighting columns. The pole’s sway in the wind, lightning protection and carrying power and data to the pole should be planned from the start; cable added later always comes at a high price. Over a wide area, fixed cameras provide observation level. A PTZ is added for detail at the moment of an incident, not as a replacement for fixed cameras.

Barrier and access system integration

The barrier, access control and cameras are three separate systems; draw the line of responsibility between them clearly. Common integration models:

  • Direct opening by plate: the LPR camera or LPR software compares the plate with an allow list and triggers the barrier control board via a relay output. It’s simple; but permission management stays inside the camera or LPR software.
  • Via the access control panel: the LPR result is passed to the access control panel like a card number (some LPR cameras offer a Wiegand output, or integration is done via API). The authorization decision is made in the central access control system; staff cards and vehicle plates can be linked to the same person record.
  • VMS-centered: the VMS receives plate events, compares them with lists and produces outputs with a rule engine. Central reporting becomes easier in multi-site setups.

Whichever model is chosen, the barrier’s safety logic isn’t left to the camera system. The safety loop under the arm or a photocell prevents the arm from coming down while a vehicle is under the barrier; this function stays in the barrier control board. What happens when the camera system is out of service should also be written down: card access, remote opening via intercom or manual mode. For setups combining card access and camera recordings in the same event, you can start from the card access and camera integration page.

Pedestrian areas and payment points

A significant share of car park incidents happen to pedestrians, not vehicles. Lift doors, stair exits, pedestrian doors and automatic payment machines are points where people must be seen at recognition or identification level. The camera is placed at an angle where the face isn’t backlit and with a tilt close to eye level.

At a payment machine, the camera shows the person standing in front and the transaction; however, the card PIN keypad and the payment information on screen mustn’t fall into the recorded area. If needed, a privacy mask is applied to the keypad zone. At emergency call and intercom buttons, having the relevant camera’s image appear on the operator screen automatically when the button is pressed is a simple but effective integration. It shortens response time.

Car parks in residential complexes require different rules for the management structure and residents’ privacy; we covered this scenario in the residential complex and apartment common area camera systems article.

Setup checklist

  • Are a separate plate camera and a separate overview camera planned for each lane?
  • Does the plate stay in the middle of the read zone while the vehicle stops over the loop detector?
  • Was the night test done with a vehicle with its headlights on, at real entry speed?
  • Does the barrier safety loop or photocell work independently of the camera system?
  • Is a fallback flow defined for when LPR can’t read?
  • In an indoor car park, are parking spaces behind columns seen from a second angle?
  • At payment machines, is the PIN keypad outside the recorded area or masked?
  • Are all cameras and the LPR software tied to the same NTP source?

For a survey and implementation covering the whole car park, see the car park and vehicle entry–exit camera solutions page, and for the plate reading layer the license plate recognition systems page.

Frequently asked questions

Does a plate camera replace an overview camera in a car park?

No. A plate camera is tuned for reading plates with a narrow field of view, short exposure and strong IR; the vehicle’s color, model and the driver often can’t be made out in this image. A separate overview camera is needed in each lane for incident review.

How does headlight glare at night affect plate reading?

Because a camera reading the front plate looks directly at the headlights, the plate area can be lost in the glare. Bringing out the retroreflective plate with IR illumination, using a short exposure time and, where appropriate, reading the rear plate reduces the problem.

Should the barrier open by plate or by card?

Both models are used. Opening by plate improves the user experience but needs a fallback flow for read errors. In corporate settings, keeping the authorization decision in the access control system makes it easier to link the plate and the staff card to the same person record.

What camera type is best for an indoor car park?

Fixed dome cameras with corridor mode are common in driving aisles, and wide-angle or fisheye cameras at ramps and junctions. Blind spots created by columns should be covered with a second camera from the opposite direction.

Support

Contact us for support or a discovery session on this topic.

Contact form
[email protected]

Eretek Video Surveillance

IP cameras, recording and central management infrastructure. We plan blind spots, retention periods and the camera network around the risks of each site.

Knowledge Center

Other articles