IP and IK Ratings for Outdoor Cameras: Choosing and Mounting Correctly

What do IP66, IP67 and IK10 cameras tell you, and what don’t they? Reading IEC 60529 and IEC 62262, selection by environment, temperature, corrosion and water ingress through cable entries.
Technical summary
Technology
IEC 60529 (IP code), IEC 62262 (IK code), ISO 9223 corrosion categories, cable glands, outdoor camera housings
Topic
Choosing outdoor cameras by resistance to dust, water, impact and environment
Level
Beginner–intermediate
Prerequisites
  • Reading camera datasheets
  • Site survey and mounting point information
In this article8 sections

A dome that fogs inside after rain, a housing that takes in water through the cable entry, a mounting bracket rusting on the coast within two seasons. All three say “IP67” or “IK10” on the datasheet. The problem isn’t the code; it’s not knowing what the code tests and what it doesn’t cover. Below we unpack the IEC 60529 IP codes and IEC 62262 IK impact ratings, and show how to choose an outdoor camera together with temperature, corrosion and mounting details, and where protection is lost on site.

How to read the IP code

The IP (Ingress Protection) code is defined in IEC 60529 and gives an enclosure’s protection against solid objects and water in two digits. The first digit is solids and dust, the second is water. “X” is written for a property that hasn’t been tested (for example IPX6).

Number First digit: solid objects Second digit: water
4 Objects larger than 1 mm Splashing water from any direction
5 Dust protected (limited ingress, doesn’t impair operation) Water jets (6.3 mm nozzle)
6 Dust tight Powerful water jets (12.5 mm nozzle)
7 — Temporary immersion (up to 1 m, 30 minutes)
8 — Continuous immersion (conditions specified by the manufacturer)
9 — High-pressure, high-temperature water jets

The detail most often missed in specifications: under IEC 60529, immersion tests (7 and 8) and jet tests (5 and 6) measure different behavior, and it can’t be assumed that an IP67 product also passes the IP66 test. A product declaring resistance to both conditions is dual-marked “IP66/IP67.” For a façade camera exposed to rain and wash hoses, the meaningful value is usually IP66.

Immersion only comes to the fore if there’s a risk of standing water or flooding.

In areas washed with high-pressure, hot water (food facilities, vehicle wash bays), you see IPX9 or the IP69K marking from the automotive standard ISO 20653. These hygienic environment requirements are covered separately in the camera selection for food production facilities article.

IK impact ratings

The IK code is defined in IEC 62262 and gives the resistance of an electrical equipment enclosure to mechanical impact as impact energy (joules). Cameras usually range from IK08 to IK10.

Class Impact energy Meaning for cameras
IK07 2 J Light accidental knocks
IK08 5 J Indoors at reachable height
IK09 10 J Public areas, medium vandalism risk
IK10 20 J Reachable outdoors, high vandalism risk

The 20 J of IK10 corresponds to a 5 kg mass falling from a height of 40 cm. It doesn’t mean “unbreakable.” Repeated impacts, sharp objects or attempts to pry it off with a crowbar are outside the scope of the test. The IK value is given for the housing; when the dome is scratched, the image degrades regardless of the IK rating. At points with high vandalism risk, IK10 alone isn’t enough: concealed cable entry, tamper-proof screws and mounting height are planned together.

Selection table by environment

Medium IP recommendation IK recommendation Extra attention
Under eaves, façade sheltered from rain IP66 Depending on reachability Condensation, spider webs
Exposed façade, pole IP66 (or IP66/IP67) Depending on reachability Sun, wind vibration
Low, reachable point IP66 IK10 Concealed cabling, tamper-proof screws
Washed areas (food, vehicle wash) IP66 + IPX9 / IP69K IK08–IK10 Chemical-resistant housing
Coast, port, chemical plant IP66/IP67 Depending on reachability Stainless housing, corrosion category
Dusty production, mining, cement IP6X (dust tight) IK08 and above Lens cleaning, wiper

Don’t skip the “Extra attention” column even for a camera under the eaves. A spider web reflecting IR light at night is one of the frequent “blurry image” calls. Areas with explosion risk (ATEX/IECEx) are outside this table; there, IP and IK are only additional requirements. The topic is in the Ex-proof camera selection for ATEX zones article.

Operating temperature and heaters

The IP rating tells you about sealing, not temperature resistance. The temperature range on the datasheet is a separate selection criterion and may contain two different values:

  • Operating range: The ambient temperature the camera withstands while running. The internal temperature of a dark housing in the sun rises well above ambient. That’s why a sun shield isn’t a decorative accessory but often a necessity.
  • Cold start: The lower limit at which the camera, switched off in freezing cold, can safely start when re-energized. Heated models warm the housing first and then give an image. On a site where long power outages can occur, this value is decisive.

Heaters and fans increase PoE consumption markedly. The datasheet gives maximum consumption with the “heater on” separately; calculate the switch and PoE budget based on this value. A camera that runs fine in summer and starts restarting at the first cold spell shows the budget was done with the heater-off value. The heater’s other job is to prevent fogging on the dome or front window; for fogging in cold, humid environments, see the cold storage cameras article.

Corrosion and salty environments

An IP67 housing can rot within a few years in salty air. The IP test doesn’t measure corrosion. The severity of atmospheric corrosion is divided into categories in ISO 9223, from C1 (very low) to C5 (very high) and CX (extreme); coastlines, ports and some chemical plants fall into the upper categories.

What to look for when choosing:

  • Housing material: A painted aluminum housing becomes open to corrosion wherever the paint is damaged. For marine environments, manufacturers usually offer a series with a 316L stainless steel housing.
  • Test declaration: If the manufacturer provides a declaration on salt spray tests (for example ISO 9227 or IEC 60068-2-52) and test duration, ask for it. “Corrosion-resistant” written without a test name can’t be compared.
  • Mounting bracket and screws: Mounting a stainless housing with a galvanized bracket and ordinary steel screws moves the weak link to the bracket. Galvanic corrosion occurs where different metals touch; choose bracket, screw and gland materials compatible with the housing.
  • Connectors: RJ45 and power connectors in the junction box are also affected by corrosion. Don’t leave them exposed in a humid environment.

Pole, earthing and corrosion design in ports and wide open areas is treated as a whole in the port and open-area camera design article.

Loss of protection at cable entries and in mounting

In enterprise camera systems, most water and dust problems on site come not from the camera but from the installation work. A camera that’s IP66 in the lab isn’t IP66 on site if the cable entry isn’t sealed properly. The installation team protects the code.

  • Cable pigtail and RJ45 protection kit: Most cameras come with a short cable tail and a waterproof cap kit for the exposed RJ45. A connection wrapped in insulating tape instead of the kit takes in water over time; the tape draws water in by capillary action.
  • Junction box: Make the cable splice inside the camera’s dedicated junction box, and seal the box with a gland matching its IP rating.
  • Unused entries: Close empty cable entries on the housing or box with the manufacturer’s blanking plugs.
  • Drip loop: Bring the cable to the entry from below with a “U” loop; water running along the cable drips off before reaching the entry.
  • Gland fit: The gland must match the cable’s outer diameter. A gland that doesn’t fit the diameter won’t seal, however much it’s tightened.
  • Dome and gasket: After installation and maintenance, close the dome or front cover with the torque and sequence specified by the manufacturer; don’t leave the gasket dirty or crushed. On some models, the desiccant pack inside the housing is replaced every time the cover is opened.

The order of checks on a camera that has taken in water is clear: first the cable entry and RJ45 kit, then the glands and blanking plugs, and last the dome gasket. Look at these three before blaming the housing.

Selection checklist

In quotation comparison and the specification, ask for a clear answer to each item below:

  • What exactly is the IP code (IP66, IP67, IP66/IP67)? To which standard, and was it tested in an independent laboratory?
  • Is the IK rating declared for the whole housing or only the dome?
  • What are the operating temperature range and the cold start temperature? If there’s a heater, what is the maximum power consumption?
  • What is the estimated corrosion category of the site? Are the housing, bracket and screw materials suitable for this category?
  • How is the cable entry protected? Are the RJ45 waterproof kit and junction box included in the delivery?
  • Are accessories such as a sun shield, wiper or desiccant needed for the environmental conditions?
  • Is it being mounted at a point at risk of lightning and surges? (This topic is covered in the lightning and surge protection article.)

Use the IEC publications catalog for the current versions and scope of the standards. In our outdoor and perimeter security cameras and enterprise IP camera installation services, we apply this checklist item by item on site when designing housings and mounting suited to site conditions.

Frequently asked questions

Is an IP67 camera better than an IP66 one?

Not always. IP67 refers to a temporary immersion test and IP66 to a powerful water jet test; one doesn’t automatically cover the other. For a façade camera exposed to rain and hose washing, IP66 is more meaningful. If both are needed, choose a product dual-marked IP66/IP67.

Is an IK10 camera unbreakable?

It can break. IK10 shows the housing withstands a standard 20 J impact. Repeated impacts, sharp objects or removal attempts aren’t within the scope of the test. At points with high vandalism risk, also plan mounting height and concealed cable entry.

Is an IP67 camera enough in a coastal area?

No; the IP rating doesn’t measure corrosion resistance. In a salty environment, assess the housing material, salt spray test declaration and the material of the mounting bracket and screws separately; if needed, choose a series with a stainless steel housing.

Why did my camera take in water even though it’s IP66?

The most common cause is the cable entry: not using the RJ45 protection kit, an unsuitable gland, an unsealed cable entry or no drip loop. A dome gasket not closed properly after maintenance is also common.

Support

Contact us for support or a discovery session on this topic.

Contact form
[email protected]

Eretek Video Surveillance

IP cameras, recording and central management infrastructure. We plan blind spots, retention periods and the camera network around the risks of each site.

Knowledge Center

Other articles